About seller
Extreme ultraviolet lithography (EUVL) presents promise for the advanced technology node in the manufacturing of integrated circuits. The imaging performance of EUVL is significantly affected by the aberration of projection optics. To obtain one optimum aberration for different test patterns, an inverse optimization method for aberration is proposed in this paper. The aberration models of three types of test patterns are first established by applying the backpropagation (BP) neural network. Then choosing the common indicators of the lithography process variation band (PVB) and pattern shift (PS) as the objective function, an aberration optimization method based on the algorithm of simulated annealing is proposed. After applying the optimization method, a set of optimized aberrations and the corresponding PVBs and PSs are obtained and analyzed. MI-773 These results are finally compared with those from rigorous simulations. The comparison results show that zero aberration is non-optimal distribution in EUVL image simulation with mask topography. In addition, the high prediction accuracy and robustness of aberration optimization is also demonstrated from the results.The present study examines the scattered light intensity from a drop passing through a Gaussian beam of a diameter comparable to or smaller than the drop. This is the situation encountered when using the time-shift technique, an optical technique used to characterize drops and aerosols according to the size and the velocity. In simulating the signals received by such an instrument, the computational effort involved when using, for instance, the Generalized Lorenz-Mie Theory or vector ray-tracing, is immense and hardly practical for use in instrument design and/or optimization. In this study theoretical expressions based on geometric optics are derived as an alternative, and they are shown to adequately capture the main features of the time-shift signals. These solutions require little computational effort and can be effectively used to explore the dependencies of the signals on various input factors, thus allowing further instrument development. On the other hand, these relations are also of general interest in the field of light scattering from drops and aerosols.The optical aberrations of the thermal lens formed in a liquid are reported for the first time as expressed in terms of the Zernike polynomials coefficients. Convection of the liquid in which the thermal lens is formed is shown to strongly modify the lens imaging properties, even for the case of vertical heating laser illumination, as studied herein. The time evolution of the optical properties of the thermal lens is investigated. The direction from which the heating laser beam illuminates the thermo-optical liquid, in which the thermal lens is formed, has been found to be crucial for the lens optical power, type, and level of aberrations observed and the way these lens properties change in time.Passive all-weather windows, capable of selectively transmitting visible and infrared solar radiation, could help in bringing down fossil-fuel energy consumption globally by reducing the carbon footprint of typical air-conditioning systems for buildings and motor vehicles. Here, we report on designing metal-insulator-metal thin-films for application in passive windows, optimized for different climatic conditions. We analyze designs comprising different noble metals as well as their relatively inexpensive alternatives. By finding an optimal choice of materials and thicknesses of the metal and dielectric layers, our lithography-free simple design can provide all-weather solutions for passive windows with desired visible and infrared transmission/blocking capability. Obtained theoretical results agree well with full-wave simulations. Thus, our proposed designs enable developing low-cost, ultra-thin (thickness 47-85 nm), polarization-independent, angle-insensitive (up to 83 deg), and large-area-compatible passive windows with improved solar-radiation control for different weather/climatic conditions. The figure-of-merit calculation shows that the relatively inexpensive metals used in our passive glasses can outperform industry-standard commercial glasses and previously reported infrared-blocking plasmonic glasses.Methods of three-dimensional deconvolution (3DD) or volumetric deconvolution of optical complex-valued wavefronts diffracted by 3D samples with the 3D point spread function are presented. Particularly, the quantitative correctness of the recovered 3D sample distributions is addressed. Samples consisting of point-like objects can be retrieved from their 3D diffracted wavefronts with non-iterative (Wiener filter) 3DD. Continuous extended samples, including complex-valued (phase) samples, can be retrieved with iterative (Gold and Richardson-Lucy) 3DD algorithms. It is shown that quantitatively correct 3D sample distribution can be recovered only with iterative 3DD, and with the optimal protocols provided. It is demonstrated that 3DD can improve the lateral resolution to the resolution limit, and the axial resolution can be at least four times better than the resolution limit. The presented 3DD methods of complex-valued optical fields can be applied for 3D optical imaging and holography.To deal with the requirement of high-precision localization of large-size workpieces in an industrial environment, an improved shape-based matching algorithm is proposed based on the phase stretching transformation and the iterative closest point algorithms. Basler industrial cameras are used to collect images of large-size workpieces, such as glass. The experimental results show that the average localization error is 0.05±0.013mm, which can meet the requirements of practical applications. This algorithm can effectively and accurately achieve high-precision localization of different positions of multi-directionally transformed objects in industrial environments.Aiming to investigate the connection between camera structure and optical systems, a comprehensive analysis needs to be performed for the airborne camera. An integrated analysis method was proposed to design and analyze optical and mechanical structures. Based on the designed small airborne camera, the impact of microvibration on the optical performance of the airborne camera was studied by integrated optomechanical analysis. In addition, the change of optical surface accuracy was analyzed. First, static and dynamic analysis of the designed airborne camera was performed to verify the stability of the camera structure and obtain the data for integrated optomechanical analysis. Then, a calculation method for rigid body displacement was proposed, and the impact of rigid body displacements on the optical system was analyzed. To evaluate the change of surface accuracy, the parameters root mean square (RMS) and peak to valley (PV) were calculated by fitting the surface distortion data. Based on the Zernike polynomial coefficients, the response of the optical system was calculated and analyzed utilizing ZEMAX to analyze the impact of microvibration on the optical performance of the airborne camera.