About seller
The stresses and deformations in the periodontal ligament (PDL) under the realistic kinetic loading of the jaw system, ., chewing, are difficult to be determined numerically as the mechanical properties of the PDL is variably present in different finite element (FE) models. This study was aimed to conduct a dynamic finite element (FE) simulation to investigate the role of the PDL (PDL) material models in the induced stresses and deformations using a simplified patient-specific FE model of a human jaw system. To do that, a realistic kinetic loading of chewing was applied to the incisor point, contralateral, and ipsilateral condyles, through the experimentally proven trajectory approach. Three different material models, including the elasto-plastic, hyperelastic, and viscoelastic, were assigned to the PDL, and the resulted stresses of the tooth FE model were computed and compared. The results revealed the highest von Mises stress of 620.14 kPa and the lowest deformation of 0.16 mm in the PDL when using formation for the medical and biomechanical experts in regard of the role of the material models being used to address the mechanical behavior of the PDL in other components of the tooth. The purpose of this in vitro laboratory study was to gauge the nanomechanical properties of the tooth enamel surface using home and in-office bleaching products. Thirty-six extracted lower lateral incisor teeth (sound and without caries, cracks or restorations) were selected. A silicone mould was used to affix the samples in resin after cutting away the roots. Next, the samples were indiscriminately divided into three treatment groups, i.e., 12 teeth in each study group (control, Opalescence Home, and Opalescence Boost), and treated according to their respective group procedures. Surface topography, nano-indentation, and visual analyses were performed. Data were examined statistically using one-way analysis of variance (p < 0.05). Both experimental bleaching products enhanced the surface roughness when compared to the samples in the control group. However, the control and Opalescence Boost groups showed insignificant differences. The lowest mean nanohardness (GPa) was observed in the Opalescence Boost group (1.56 GPa ± 0.68 GPa). In contrast, the highest mean nanohardness (GPa) was perceived in the control group (3.53 GPa ± 1.06 GPa). The modulus of elasticity was highly affected using Opalescence Boost (182.63 GPa ± 109.13 GPa) when compared to Control (322.69 GPa ± 168.24 GPa). On visual examination, pronounced roughness was observed in both the Opalescence Home and Opalescence Boost groups. Both teeth whitening products damaged the enamel surface either by roughening the tooth surface or by affecting the nanomechanical properties. Therefore, teeth whitening products may be used, but with great caution.Both teeth whitening products damaged the enamel surface either by roughening the tooth surface or by affecting the nanomechanical properties. Therefore, teeth whitening products may be used, but with great caution. The aim of the study was to investigate the efficacy of two toothbrushing techniques on the amount of plaque accumulation and to evaluate how the changes were correlated to the anatomical characteristics of the anterior maxillary arch. Thirty subjects of both genders were included, they were asked not to brush for 12 h. Afterwards, they were asked to manually brush the left side of their maxillary arch with the modified Bass technique and the right side adopting the roll technique. The comparison of photographs taken before and after the manoeuvres, using a plaque disclosing agent, allowed the researchers to measure the changes in plaque accumulation measured using the Quigley and Hein plaque scoring classification. Linear regression analysis was used to evaluate the correlation between such changes and the teeth and arch anatomical characteristics. A mean reduction of 9.6 ± 5.2% considering both arches after brushing was observed. The changes in plaque accumulation were not different between the two tehe teeth characteristics. Success of Dental Program depends on the students' performance measured in terms of Program Learning Outcomes (PLOs) achievement. The present study was carried out to evaluate the level of achievement of the PLOs among dental interns and fresh graduates as a direct measure for the success of the BDS program of the College of Dentistry, King Saud University. An online survey instrument was used to seek the opinion of male and female dental interns and fresh graduates about the attainment of the PLOs distributed over 6 domains patients' care, communication & interpersonal skills, professionalism, practice management, information management & critical thinking, and health promotion domains on a five-point Likert scale. The data were analyzed using Minitab Statistical Software version 15.1.31.0. Descriptive as well as Chi-Square statistics were calculated to determine the significance of the responses to the levels of PLOs achievement at 0.05 level of significance. Levels of achievement of PLOs undeevealed significant achievement of PLOs under all learning domains of the BDS curriculum taught at the College of Dentistry, King Saud University. However, achievement scores for Information Management, Critical Thinking, and Health Promotion domains require further improvement through reinforcement of the curriculum, updating of content, and teaching strategies. Bibliometric analysis of best-cited papers brings awareness about the influential publications and trends in the literature on a particular topic. Linsitinib This will help not only the researchers and academicians but also the students for selecting quality landmark articles. With this view in mind a bibliometric analysis was performed to identify the 100 top-cited papers on Forensic Odontology (FO) in the literature. A search was performed using Scopus database in August 2019. The articles were further reviewed and basic standard information related to bibliometric analysis was recorded. The 100 most cited articles were published from 1985 to 2014 (77% published after 2001). The most frequently cited article received 259 citations, whereas the least received 31 (mean citations 58.78±33.14). There were 16 different journals with Forensic Science International having the most number of articles (n=36). One author had 16 articles while 8 authors had 4 or more articles published in the top 100 list. Belgium was the country with most number of articles (n=17) followed by United States (n=16).